this post was submitted on 15 Oct 2024
105 points (98.2% liked)

Bicycles

3297 readers
4 users here now

Welcome to !bicycles@lemmy.ca

A place to share our love of all things with two wheels and pedals. This is an inclusive, non-judgemental community. All types of cyclists are accepted here; whether you're a commuter, a roadie, a MTB enthusiast, a fixie freak, a crusty xbiking hoarder, in the middle of an epic across-the-world bicycle tour, or any other type of cyclist!


Community Rules


Other cycling-related communities

founded 2 years ago
MODERATORS
 

I wanted to share my experience with waxing my bike chains.

I was resistant to waxing my chains because it seems that a lot of people felt it was "too much work".

But having to constantly clean black shit off my chains after every ride, then spend time degreasing and re-lubing, I figured I'd try waxing when I got my gravel bike.

Now, thousands of KM later and having converted all three bikes to waxed, there's no way I'd go back. The time saved could be measured in hours per month.

First, the biggest complaint is chain prep. Yeah, regardless if you're waxing or not, you'll need to prep a new chain by removing the factory grease. With waxed, you do this once, and no more worrying about degreasing ever again. Make like easy and get Silca's chain stripper, and it's a 10 minute, one-step process.

Ongoing chain maintenance couldn't be easier. After every ride, give the chain a quick wipe (or not). My chain stays clean, even after a 200 km ride.

And if you ride in wet or dirty conditions? Guess what, you're in for a LOT of work if you lube your chain. With waxed, keep a second (or third) chain ready to go, and you just swap it out (10 seconds of effort). Take the dirty chain, give it a wipe if it's only been wet, or pour boiled water onto it if you want to "reset" the chain to bare metal. Then drop it into the waxing pot for a re-wax. You don't have to stand at the pot, so there's no real time commitment here. I've spent more time completely dirtying large microfiber cloths trying to get my chain "clean" when lubed (hint: it's never clean if you use a wet lube, not without solvents and an ultrasonic cleaner).

For actual immersion wax, I do it every 1000 km (sooner than you need to), and use a drip wax every 200 - 250 km to keep things fresh.

Honestly, wax is easier, cleaner, and takes less time to maintain vs wet lube.

The only downsides? The initial cost to get started. But this is offset by not having to replace chains or other components prematurely. You actually save money in the long-term when using waxed chains.

Some might argue that "you can't run waxed chains in muddy or constantly rainy conditions". Well, at the same time, your wet lube isn't really helping matters in those situations, either. Waxed is still better, and you can swap chains much faster than you can clean the grinding paste from a wet lubed chain.

Who would I not recommend waxed chains to? Someone who rarely uses their bike. Drip lube will be "good enough" in those cases. But anyone else would benefit from waxing their chain.

(page 2) 32 comments
sorted by: hot top controversial new old
[–] thatsnothowyoudoit@lemmy.ca 2 points 4 months ago (1 children)

Started with wet wax five years ago. Two years ago migrated to immersion waxing.

I do 5-10 chains at a time. It takes all of 15 minutes.

Then I wet wax between immersion waxing sessions.

Chains last a wildly long time and the time saved in between rides is incredible. Not to mention how clean all other parts stay.

[–] Showroom7561@lemmy.ca 1 points 4 months ago (1 children)

I do 5-10 chains at a time.

For how many bikes??

[–] thatsnothowyoudoit@lemmy.ca 2 points 4 months ago (1 children)

Heheh. A few.

But I also do my partners bikes.

Most bikes have two active chains each. That way when I do it, it’s quite some time before I have to do it again.

[–] Showroom7561@lemmy.ca 1 points 4 months ago (1 children)

Are you doing anything special to clean the chains before they get rewaxed in the immersion bath?

I'm a little OCD when it comes to worrying about contamination, but I hear a lot of people just wipe the outside of the chain and stick it in the wax without issues. You probably have more experience than most, considering how many chains you wax!

[–] thatsnothowyoudoit@lemmy.ca 1 points 4 months ago (1 children)

OCD checking in here too.

To clean the chains they go in an ultrasonic cleaner with heated water to get rid of the existing wax. This makes it easy to just put all the chains in at once and let them party.

Then a second ultrasonic session with some isopropyl for a final clean and repelling the water. I have mason jars that the chains go in, so it’s really quick and repeatable. By the isopropyl step they’re already quite clean so the isopropyl lasts a really long time.

I’ve got the workflow down - and lots of place to hang chains in the bike workshop.

The same process works well for stripping new chains - just with the hot water step switched out for a mineral spirits bath. It’s just as quick but needs a space with good ventilation.

[–] Showroom7561@lemmy.ca 1 points 4 months ago

To clean the chains they go in an ultrasonic cleaner with heated water to get rid of the existing wax.

I didn't even consider using my ultrasonic cleaner with the heater on. I'm not even sure it gets hot enough, but I may give it a try!

As for isopropyl alcohol, it's a good second step, but I'm not even sure that it's necessary.

Remember that technically, we can just dump an old waxed chain into more wax, and it'll be just fine. Yes, a little contamination gets into the wax, but apparently not enough to be a problem (with as many chains as you have, I probably wouldn't want to do that).

And the Zero Friction Cycling guy even recommends two wax pots, so your "dirty" chain goes into one, and then into the second one, reducing the contaminants in the second pot.

But, I'm almost certain that simply boiling the wax off is going to be more than good enough to get the chain clean. And I think the guys at Silca say that putting a chain into oil that's a little wet is fine, since the water "boils off".

In any case, if your workflow works well, and it sounds like it does, keep doing it! I'm sure I'll modify and refine my workflow as I go (even might give the two pot method a go), but it's already "too easy" compared to all the solvent baths I used to run my chains through.

[–] DarkThoughts@fedia.io 1 points 4 months ago (4 children)

In my experience a lot of people are simply not aware of liquid chain wax like Squirt and think they have to put their chain in a heated pot or something.

[–] ghashul@feddit.dk 1 points 4 months ago

This is what I've been using for the last 12 years, and I've been happy. Immersion waxing seems interesting, but it does seem a bit daunting to me.

load more comments (3 replies)
[–] ContrarianTrail@lemm.ee 1 points 4 months ago

My chain maintenance takes about 2 minutes: soak it with some cheap multipurpose oil and wipe off the excess with an oily rag. I repeat this once every 2 weeks or so and it has worked good enough so far. When it's extra wet outside and my bike is covered in mud when I get back home I usually go thru it with an garden sprayer filled with hot water. Then I add the extra step of drying the chain with compressed air and re-lube it for storage after every ride.

[–] LukaszH@szmer.info 0 points 4 months ago (1 children)

The time saved could be measured in hours per month.

Huh? I have two bikes I ride all year round – snow, rain, sun, on and off-road. Both of them pretty well maintained, if I say so myself. I've ridden over 5.5k km this year, and I think I've spent less than an hour total on cleaning and lubing my chains.

Make like easy and get Silca’s chain stripper, and it’s a 10 minute, one-step process.

10 minutes to degrease your chain with some fancy (and expensive, I presume) stripper? Damn, nobody's got time and money for that. You can do that in less than two minutes of work, including taking the chain off and putting in back. Just put your dirty chain in a small plastic bottle with some gasoline and shake it well for a minute. After that, run it through a piece of cloth and hang outside to dry. Done.

Honestly, wax is easier, cleaner, and takes less time to maintain vs wet lube.

Yeah, sure. Not having to cook my chains every 1k km takes sooo much time xD

load more comments (1 replies)
load more comments
view more: ‹ prev next ›